Quarry School

Degrees, minutes and seconds: smaller pieces of a turn — quick review

In plain words

Picture a shop that lets you exchange one large token for 60 smaller tokens, and each small token for 60 tiny ones.

Rule

1° = 60′ = 3600″ and 1′ = 60″. Decimal degrees = D + M60 + S3600. For subtraction: 90° = 89°59′60″ and 180° = 179°59′60″.
Here D, M, and S count degrees, minutes, and seconds, respectively.

Step

  1. For DMS subtraction, align the degree, minute and second columns. If needed, borrow one degree as 60 minutes, then one minute as 60 seconds.

  2. Subtract each column after the units are available. Check by adding your answer to the original angle.

  3. For DMS to decimal degrees, keep the degrees and add minutes ÷ 60 and seconds ÷ 3600.

  4. For decimal degrees to DMS, keep the whole degrees. Multiply only the leftover decimal by 60; keep its whole minutes.

  5. Multiply the new leftover decimal minute by 60 for seconds. Round at the end; if seconds round to 60, carry one minute. If minutes reach 60, carry one degree.

  6. In the table picture, read a column under Degree, °, then compare the matching information below it. Each column preserves one complete row of the reference table.

Question

A triangular plot of land has corners P, Q and R. A surveyor measures the angle at Q as ∠Q = 48°37′25″. A mapping program lists the angle at P in decimal degrees as ∠P = 63.4333°. (a) Write ∠P in degrees, minutes and seconds, rounded to the nearest second. (b) The three angles of a triangle add to 180°. Using your answer to (a), find ∠R in degrees, minutes and seconds. (c) Write ∠R in decimal degrees, rounded to four decimal places.

Answer

(a) ∠P ≈ 63°26′0″; (b) ∠R = 67°56′35″; (c) ∠R ≈ 67.9431°

Trap

Treating DMS as decimal digits. 6′ is 660° = 0.1°, not 0.06°. Borrow and carry in groups of 60, not 100.

Strategy

  1. Read the requested operation and label the units in each column.

  2. For DMS subtraction, exchange larger pieces until each smaller column has enough, then subtract matching columns.

  3. For DMS to decimal degrees, use D + M60 + S3600 before the final rounding.

  4. For decimal degrees to DMS, keep the whole degrees, multiply the leftover by 60, keep the whole minutes, and multiply their leftover by 60.

  5. Round seconds as requested and carry complete groups of sixty.

  6. Check subtraction by addition, or check conversion by converting the unrounded value back.

Term

Line

Definition

A straight path that continues forever in both directions. Two points on it can name it.

Term

Point

Definition

An exact location. A point has no width or length.

Term

Angle

Definition

Two rays sharing an endpoint. You can also view an angle as the turn that moves one ray toward the other.

Term

Clockwise

Definition

Turning in the direction a clock's hands normally move.

Term

Minute (′)

Definition

An angle unit equal to 160 of a degree. It measures angle, not elapsed time.

Term

Second (″)

Definition

An angle unit equal to 160 of a minute or 13600 of a degree.

Term

DMS notation

Definition

Writing an angle in degrees, minutes, and seconds, with symbols °, ′, and ″.

Term

Decimal degrees

Definition

Writing an angle as a number of degrees with a decimal part instead of separate minutes and seconds.

Term

Approximation

Definition

A value close to the exact amount, often obtained by rounding. The symbol ≈ means approximately equal.

Term

Degree measurement

Definition

Expressing the amount and direction of a turn using degrees.

Term

Numerator

Definition

The top number or expression in a fraction. It counts pieces of the size named by the denominator.

Term

Denominator

Definition

The bottom number or expression in a fraction. It tells the size of each counted piece. It cannot be zero.

Term

Common denominator

Definition

A shared bottom number used to rewrite fractions into matching-sized pieces before adding or subtracting them.