Quarry School

Convert the unit, then locate a radian angle — quick review

In plain words

Think of a road sign that gives the same distance in miles and kilometers.

Rule

Degrees → radians: multiply by πradians180°. Radians → degrees: multiply by 180°πradians.
Radian coterminal angles are θ + 2πn, where n is any integer; reduce to 0 ≤ θ < 2π before locating the terminal side.

Step

  1. Identify the starting unit. A degree sign means degrees; the instructor's angle notation without that sign means radians.

  2. Write the multiplier with the starting unit on the bottom, because the matching unit on top and bottom then cancels.

  3. Multiply the numerators and denominators and reduce common factors. Treat π as one factor, because it cancels only against another π.

  4. Keep an exact π fraction when possible. If a decimal degree answer is requested, calculate from the exact expression and round at the end.

  5. To locate a radian angle, add or subtract 2π until it is in 0 ≤ θ < 2π. Use a common denominator when adding or subtracting π fractions.

  6. Compare with the exact quarter-turn boundaries. Equality means the angle is quadrantal and belongs to no quadrant; decimal landmarks are rounded guides.

  7. In the table picture, read a column under I, then compare the matching information below it. Each column preserves one complete row of the reference table.

Question

You are changing the measuring unit in both directions and locating both terminal rays. Convert 225° to radians, then convert 7π6 radians to degrees. Locate both terminal sides.

Answer

225° = 5π4 radians, Quadrant III.
7π6 radians = 210°, Quadrant III.

Trap

Using a rounded boundary such as 1.57 as though it were exactly π2. An angle of 1.57 radians is slightly below the exact axis value. Use exact π boundaries for exact angles, and use the decimals only when the angle lies clearly between them.

Strategy

  1. Identify whether the starting angle uses degrees or radians.

  2. Write the conversion fraction with the old unit underneath and the desired unit on top.

  3. Multiply, cancel matching factors, and reduce the result; keep π exact when an exact answer is requested.

  4. If location is requested, reduce negative or large angles into one revolution by full-turn additions or subtractions.

  5. Rebuild the quarter-turn boundaries and compare the reduced measure with them.

  6. Check with the opposite conversion or the angle's fraction of a half turn.

Term

Endpoint

Definition

A point where a line segment stops or where a ray begins.

Term

Ray

Definition

A straight path that begins at one endpoint and continues forever in one direction.

Term

Angle

Definition

Two rays sharing an endpoint. You can also view an angle as the turn that moves one ray toward the other.

Term

Terminal side

Definition

The ray where an angle's rotation ends.

Term

Clockwise

Definition

Turning in the direction a clock's hands normally move.

Term

Negative angle

Definition

An angle whose recorded rotation goes clockwise. Its sign describes direction, not whether its terminal side points left or right.

Term

Full revolution

Definition

One complete turn that brings a rotating ray back to its starting position. Its size is 360° or 2π radians.

Term

Standard position

Definition

An angle placement with vertex at the origin and initial side along the positive x-axis.

Term

Origin

Definition

The point (0, 0), where the x-axis and y-axis meet.

Term

x-axis

Definition

The horizontal coordinate line. Points on it have y = 0.

Term

y-axis

Definition

The vertical coordinate line. Points on it have x = 0.

Term

Positive x-axis

Definition

The part of the horizontal axis pointing right from the origin.

Term

Quadrant

Definition

One of the four open regions between the coordinate axes. The axes themselves belong to no quadrant.

Term

Coterminal angles

Definition

Angles with the same initial and terminal sides whose measures differ by an integer number of full revolutions.

Term

Circle

Definition

All the points in a flat surface that are the same distance from one center point.

Term

Center

Definition

The point inside a circle equally distant from every point on the circle.

Term

Radian

Definition

An angle unit: one radian is the central angle whose arc length equals the circle's radius.

Term

Radian measure

Definition

An angle's size expressed in radians. For a positive central angle, divide arc length by radius: θ = sr.

Term

Exact value

Definition

A value stated without rounding. Fractions and expressions containing π can preserve the full amount.

Term

Integer

Definition

A whole-number count, positive or negative, or zero. It has no fractional part.

Term

Degree measurement

Definition

Expressing the amount and direction of a turn using degrees.

Term

Numerator

Definition

The top number or expression in a fraction. It counts pieces of the size named by the denominator.

Term

Denominator

Definition

The bottom number or expression in a fraction. It tells the size of each counted piece. It cannot be zero.

Term

Common denominator

Definition

A shared bottom number used to rewrite fractions into matching-sized pieces before adding or subtracting them.